Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources5 documents: Victrex, ATI, Steel Construction Institute
Plastic PEEK
Victrex PEEK 450G (unreinforced, injection moulded), Victrex TDS rev. March 2026; Poisson from Victrex fluid-management flyer (2020-07)
Stainless Steel 316
ATI 316 (UNS S31600), annealed 1.0 mm sheet, ATI technical data sheet (2012); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
1
VICTREX PEEK 450G Technical Data SheetVictrexPlastic PEEK · Yield strength: typical, tensile yieldPlastic PEEK · Compressive strength: typical, 23 CPlastic PEEK · Flexural strength: typical, flexural stress at yield, 23 CPlastic PEEK · Elongation at break: typical, at breakPlastic PEEK · Young's modulus (stiffness): typical (nominal)Plastic PEEK · Density: typical (crystalline)Plastic PEEK · Thermal conductivity: typical, average, 23 CPlastic PEEK · Thermal expansion: average of flow/cross-flow, below Tg (<143 C)Plastic PEEK · Melting point: typical, DSCPlastic PEEK · Glass transition: onset (midpoint 150 C)Plastic PEEK · Max service temperature: UL 746B RTI, mechanical strength (continuous use index)
2
ATI 316, 316L, 317 and 317L Technical Data Sheet (2012)ATIarchived copyStainless Steel 316 · Yield strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Ultimate tensile strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Elongation at break: typical (representative), annealed, in 2 in. (51 mm)Stainless Steel 316 · Young's modulus (stiffness): typical, in tensionStainless Steel 316 · Density: typicalStainless Steel 316 · Thermal conductivity: 20–100 °CStainless Steel 316 · Thermal expansion: mean, 20–100 °CStainless Steel 316 · Specific heat: at 20 °CStainless Steel 316 · Melting point: melting rangeStainless Steel 316 · Max service temperature: oxidation (scaling) limit in air
3
VICTREX PEEK for Use in Fluid Management (2020)VictrexPlastic PEEK · Poisson's ratio: typical
4
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 316 · Poisson's ratio: design value (structural stainless steels)
5
VICTREX PEEK 450G Technical Data Sheet (2012)Victrexarchived copyPlastic PEEK · Specific heat: typical, 23 °C, DSC (Victrex PEEK 450G TDS, revision Jul 2012)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Plastic PEEK stronger than Stainless Steel 316?
Stainless Steel 316 is stronger: its yield strength is 265 MPa against 98 MPa for Plastic PEEK (2.7x).
Which is lighter, Plastic PEEK or Stainless Steel 316?
Plastic PEEK is lighter: 1,300 kg/m³ against 8,027 kg/m³ for Stainless Steel 316.
Which is stiffer, Plastic PEEK or Stainless Steel 316?
Stainless Steel 316 is stiffer: Young's modulus 200 GPa against 4 GPa for Plastic PEEK, so the same part in Stainless Steel 316 deflects less under the same load.
Which is lighter for the same job, Plastic PEEK or Stainless Steel 316?
For the same stiffness or strength: Plastic PEEK is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 316 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic PEEK
Stainless Steel 316
Stiff rod or tie (tension)
8.1x heavier
lighter
Stiff beam (bending)
15% heavier
lighter
Stiff panel or plate
lighter
1.68x heavier
Strong rod or tie
lighter
2.28x heavier
Strong beam
lighter
3.18x heavier
Strong panel or plate
lighter
3.75x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PEEK or Stainless Steel 316?
Stainless Steel 316 stretches further before it breaks: 61% elongation at break against 25% for Plastic PEEK.
Thermal
Which conducts heat better, Plastic PEEK or Stainless Steel 316?
Stainless Steel 316 conducts heat better: 14.6 W/m·K against 0.29 W/m·K for Plastic PEEK.
Which expands less with temperature?
Stainless Steel 316 expands less: 16.5 µm/m·K against 55 µm/m·K for Plastic PEEK.