Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
17-4 PH Stainless Steel Product Data Bulletin (2021)Cleveland-CliffsStainless Steel 17-4PH · Yield strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Ultimate tensile strength: typical, transverse, sheet/stripStainless Steel 17-4PH · Elongation at break: typical, transverse, in 2 in. (50.8 mm)Stainless Steel 17-4PH · Young's modulus (stiffness): H 900Stainless Steel 17-4PH · Density: H 900Stainless Steel 17-4PH · Poisson's ratio: H 900 (column)Stainless Steel 17-4PH · Thermal conductivity: at 149 °C (300 °F), H 900Stainless Steel 17-4PH · Thermal expansion: mean, 21–93 °C (70–200 °F), H 900Stainless Steel 17-4PH · Specific heat: mean, 0–100 °C, H 900Stainless Steel 17-4PH · Max service temperature: strength-retention limit (not oxidation)
3
Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PETG is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic PETG stronger than Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stronger: its yield strength is 1,275 MPa against 46.2 MPa for Plastic PETG (27.6x).
Which is lighter, Plastic PETG or Stainless Steel 17-4PH?
Plastic PETG is lighter: 1,270 kg/m³ against 7,800 kg/m³ for Stainless Steel 17-4PH.
Which is stiffer, Plastic PETG or Stainless Steel 17-4PH?
Stainless Steel 17-4PH is stiffer: Young's modulus 197 GPa against 1.94 GPa for Plastic PETG, so the same part in Stainless Steel 17-4PH deflects less under the same load.
Which is lighter for the same job, Plastic PETG or Stainless Steel 17-4PH?
For the same stiffness or strength: Plastic PETG is lighter for a stiff panel or plate, strong panel or plate; Stainless Steel 17-4PH is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
Plastic PETG
Stainless Steel 17-4PH
Stiff rod or tie (tension)
16.5x heavier
lighter
Stiff beam (bending)
1.64x heavier
lighter
Stiff panel or plate
lighter
32% heavier
Strong rod or tie
4.49x heavier
lighter
Strong beam
49% heavier
lighter
Strong panel or plate
lighter
17% heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PETG or Stainless Steel 17-4PH?
Stainless Steel 17-4PH stretches further before it breaks: 9% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, Plastic PETG or Stainless Steel 17-4PH?
Stainless Steel 17-4PH conducts heat better: 17.9 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
Stainless Steel 17-4PH expands less: 10.8 µm/m·K against 51 µm/m·K for Plastic PETG.