Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: UltiMaker, ATI, Steel Construction Institute, Eastman
Plastic PETG
Ultimaker PETG, 3D-printed specimens, XY (flat); Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS v1.00, April 29, 2022.
Stainless Steel 316
ATI 316 (UNS S31600), annealed 1.0 mm sheet, ATI technical data sheet (2012); Poisson's ratio from the Nickel Institute/SCI structural stainless design manual
ATI 316, 316L, 317 and 317L Technical Data Sheet (2012)ATIarchived copyStainless Steel 316 · Yield strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Ultimate tensile strength: typical (representative), annealed 1.0 mm sheetStainless Steel 316 · Elongation at break: typical (representative), annealed, in 2 in. (51 mm)Stainless Steel 316 · Young's modulus (stiffness): typical, in tensionStainless Steel 316 · Density: typicalStainless Steel 316 · Thermal conductivity: 20–100 °CStainless Steel 316 · Thermal expansion: mean, 20–100 °CStainless Steel 316 · Specific heat: at 20 °CStainless Steel 316 · Melting point: melting rangeStainless Steel 316 · Max service temperature: oxidation (scaling) limit in air
3
Design Manual for Structural Stainless Steel, 4th Edition (P413)Steel Construction Institutearchived copyStainless Steel 316 · Poisson's ratio: design value (structural stainless steels)
4
Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic PETG is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Plastic PETG stronger than Stainless Steel 316?
Stainless Steel 316 is stronger: its yield strength is 265 MPa against 46.2 MPa for Plastic PETG (5.74x).
Which is lighter, Plastic PETG or Stainless Steel 316?
Plastic PETG is lighter: 1,270 kg/m³ against 8,027 kg/m³ for Stainless Steel 316.
Which is stiffer, Plastic PETG or Stainless Steel 316?
Stainless Steel 316 is stiffer: Young's modulus 200 GPa against 1.94 GPa for Plastic PETG, so the same part in Stainless Steel 316 deflects less under the same load.
Which is lighter for the same job, Plastic PETG or Stainless Steel 316?
For the same stiffness or strength: Plastic PETG is lighter for a stiff panel or plate, strong rod or tie, strong beam, strong panel or plate; Stainless Steel 316 is lighter for a stiff rod or tie (tension), stiff beam (bending).
Part that must be
Plastic PETG
Stainless Steel 316
Stiff rod or tie (tension)
16.3x heavier
lighter
Stiff beam (bending)
1.61x heavier
lighter
Stiff panel or plate
lighter
35% heavier
Strong rod or tie
lighter
10% heavier
Strong beam
lighter
1.97x heavier
Strong panel or plate
lighter
2.64x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Plastic PETG or Stainless Steel 316?
Stainless Steel 316 stretches further before it breaks: 61% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, Plastic PETG or Stainless Steel 316?
Stainless Steel 316 conducts heat better: 14.6 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
Stainless Steel 316 expands less: 16.5 µm/m·K against 51 µm/m·K for Plastic PETG.