Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources4 documents: Kaiser Aluminum, Celanese, U.S. Department of Defense
Aluminum 7050-T7451
7050-T7451 plate, Kaiser Aluminum sheet, coil & plate typical datasheet (longitudinal); Poisson from MIL-HDBK-5J
Plastic UHMWPE
Celanese GUR 4120 (avg. molecular weight 4.7x10^6 g/mol), typical values on compression-molded specimens; CTE and thermal conductivity from Celanese's generic UHMWPE guide (grade not named)
GUR UHMW-PE Overview (GUR-015)CelanesePlastic UHMWPE · Yield strength: typical, tensile stress at yield ISO 527, 50 mm/minPlastic UHMWPE · Ultimate tensile strength: typical, tensile stress at break ISO 527, 50 mm/minPlastic UHMWPE · Elongation at break: typical, nominal elongation at break ISO 527Plastic UHMWPE · Young's modulus (stiffness): typical, tensile modulus ISO 527, 1 mm/minPlastic UHMWPE · Density: typicalPlastic UHMWPE · Melting point: DSC 10 K/minPlastic UHMWPE · Max service temperature: recommended max constant operating temperature
3
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7050-T7451 · Poisson's ratio: typical (handbook physical constant)
4
GUR UHMW-PE Polymer Guide (GUR-003)Celanesearchived copyPlastic UHMWPE · Thermal conductivity: typical, unfilled (narrative value, generic Celanese UHMWPE)Plastic UHMWPE · Thermal expansion: typical, 20 to 100 °C (generic Celanese UHMWPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 7050-T7451 stronger than Plastic UHMWPE?
Aluminum 7050-T7451 is stronger: its yield strength is 469 MPa against 20 MPa for Plastic UHMWPE (23.4x).
Which is lighter, Aluminum 7050-T7451 or Plastic UHMWPE?
Plastic UHMWPE is lighter: 930 kg/m³ against 2,830 kg/m³ for Aluminum 7050-T7451.
Which is stiffer, Aluminum 7050-T7451 or Plastic UHMWPE?
Aluminum 7050-T7451 is stiffer: Young's modulus 70.3 GPa against 0.66 GPa for Plastic UHMWPE, so the same part in Aluminum 7050-T7451 deflects less under the same load.
Which is lighter for the same job, Aluminum 7050-T7451 or Plastic UHMWPE?
For the same stiffness or strength: Aluminum 7050-T7451 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 7050-T7451
Plastic UHMWPE
Stiff rod or tie (tension)
lighter
35x heavier
Stiff beam (bending)
lighter
3.39x heavier
Stiff panel or plate
lighter
1.56x heavier
Strong rod or tie
lighter
7.71x heavier
Strong beam
lighter
2.69x heavier
Strong panel or plate
lighter
1.59x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7050-T7451 or Plastic UHMWPE?
Plastic UHMWPE stretches further before it breaks: 465% elongation at break against 11% for Aluminum 7050-T7451.
Thermal
Which conducts heat better, Aluminum 7050-T7451 or Plastic UHMWPE?
Aluminum 7050-T7451 conducts heat better: 157 W/m·K against 0.4 W/m·K for Plastic UHMWPE.
Which expands less with temperature?
Aluminum 7050-T7451 expands less: 23.5 µm/m·K against 200 µm/m·K for Plastic UHMWPE.