Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
3
Wieland-Z30 (CuZn39Pb2, C37700) Data SheetWielandarchived copyBrass C360 · Poisson's ratio: base material: leaded free-machining brass CuZn39Pb2 (C37700), Wieland-Z30 rolled products, reference value at room temperature
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Brass C360 stronger than Nickel Inconel 718?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 310 MPa for Brass C360 (3.89x).
Which is lighter, Brass C360 or Nickel Inconel 718?
Nickel Inconel 718 is lighter: 8,221 kg/m³ against 8,498 kg/m³ for Brass C360.
Which is stiffer, Brass C360 or Nickel Inconel 718?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 96.5 GPa for Brass C360, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Brass C360 or Nickel Inconel 718?
For the same stiffness or strength: Nickel Inconel 718 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Brass C360
Nickel Inconel 718
Stiff rod or tie (tension)
2.14x heavier
lighter
Stiff beam (bending)
49% heavier
lighter
Stiff panel or plate
32% heavier
lighter
Strong rod or tie
4.02x heavier
lighter
Strong beam
2.56x heavier
lighter
Strong panel or plate
2.04x heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Brass C360 or Nickel Inconel 718?
Brass C360 stretches further before it breaks: 25% elongation at break against 20% for Nickel Inconel 718.
Thermal
Which conducts heat better, Brass C360 or Nickel Inconel 718?
Brass C360 conducts heat better: 116 W/m·K against 11.4 W/m·K for Nickel Inconel 718.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 20.5 µm/m·K for Brass C360.