Materials / Compare
DMLS AlSi10Mg Aluminum vs. Plastic PETG
Compare DMLS AlSi10Mg Aluminum vs. Plastic PETG strength, stiffness, weight and thermal properties.
| Mechanical | DMLS AlSi10Mg Aluminum | Plastic PETG |
|---|---|---|
| Yield strength | 270MPa15.84x stronger | 46.2MPa2 |
| Ultimate tensile strength | 450MPa19.74x stronger | 46.2MPa2 |
| Flexural strength | not sourced | 78.9MPa2 |
| Elongation at break | 10.2%134% more ductile | 7.6%2 |
| Young's modulus (stiffness) | 72GPa337.1x stiffer | 1.94GPa2 |
| Density | 2,670kg/m³4 | 1,270kg/m³22.1x lighter |
| Strength to weight | 101kN·m/kg2.78x higher | 36.4kN·m/kg |
| Stiffness to weight | 27MN·m/kg17.7x higher | 1.53MN·m/kg |
| Poisson's ratio | base material0.335 | not sourced |
| Shear modulus | 27.1GPa | not sourced |
| Bulk modulus | 70.6GPa | not sourced |
| Speed of sound | 5,193m/s4.2x faster | 1,236m/s |
| Thermal | DMLS AlSi10Mg Aluminum | Plastic PETG |
|---|---|---|
| Thermal conductivity | 110W/m·K1524x more heat through a fin | base material0.21W/m·K6 |
| Thermal expansion | mean 25-100 °C20µm/m·K12.55x less | base material51µm/m·K6 |
| 100 mm part over a 50 °C swing | 100µm growth2.55x less | 255µm growth |
| Specific heat | base material963J/kg·K5 | base material1,300J/kg·K6 |
| Heats up and cools (diffusivity) | 42.8mm²/s336x faster | 0.127mm²/s |
| Thermal shock resistance | 13,819W/m | not sourced |
| Glass transition | not sourced | 77.4°C2 |
| Max service temperature | not sourced | HDT 0.455 MPa76.2°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources6 documents: EOS GmbH, UltiMaker, Renishaw, U.S. Department of Defense, Eastman
- DMLS AlSi10Mg Aluminum
- EOS Aluminium AlSi10Mg (powder 9011-0024), EOS M 290 | 30 µm process (AlSi10Mg_FlexM291 2.01), as manufactured, horizontal; machined (turned) specimens, ISO 6892-1 B10
- Plastic PETG
- Ultimaker PETG, 3D-printed specimens, XY (flat); Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS v1.00, April 29, 2022.
- 1EOS Aluminium AlSi10Mg Material Data SheetEOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Yield strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Ultimate tensile strength: typical, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Elongation at break: typical at break, as manufactured, horizontalDMLS AlSi10Mg Aluminum · Thermal conductivity: typical, as manufactured, horizontal (ISO 22007-2)DMLS AlSi10Mg Aluminum · Thermal expansion: mean 25-100 °C, ASTM E228
- 2Ultimaker PETG Technical Data Sheet, v1.00UltiMakerarchived copyPlastic PETG · Yield strength: typicalPlastic PETG · Ultimate tensile strength: typical, peak stress (= stress at yield)Plastic PETG · Flexural strength: typicalPlastic PETG · Elongation at break: typicalPlastic PETG · Young's modulus (stiffness): typicalPlastic PETG · Density: typicalPlastic PETG · Glass transition: typicalPlastic PETG · Max service temperature: HDT 0.455 MPa (printed specimens)
- 3RenAM 500 Series Aluminium AlSi10Mg Material Data SheetRenishawDMLS AlSi10Mg Aluminum · Young's modulus (stiffness): same material and process, different machine maker: Renishaw RenAM 500, 30 µm, as built, horizontal (XY)
- 4EOS Aluminium AlSi10Mg Material Data Sheet, FlexLine, M 290 (2018)EOS GmbHarchived copyDMLS AlSi10Mg Aluminum · Density: typical part density (ISO 3369), EOS M 290, AlSi10Mg_030_FlexM291 (30 µm)
- 5MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseDMLS AlSi10Mg Aluminum · Poisson's ratio: base material: cast Al-Si-Mg alloy 359.0 (Al-9Si-0.6Mg, closest MIL-HDBK-5J alloy to AlSi10Mg / EN AC-43000)DMLS AlSi10Mg Aluminum · Specific heat: base material: cast Al-Si-Mg alloy 359.0 (MIL-HDBK-5J), at 100 °C
- 6Eastar Copolyester 6763 Product Data SheetEastmanPlastic PETG · Thermal conductivity: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Thermal expansion: base material: Eastman Eastar Copolyester 6763 (PETG), typicalPlastic PETG · Specific heat: base material: Eastman Eastar Copolyester 6763 (PETG), DSC at 60 °C (lowest temperature listed)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
DMLS AlSi10Mg Aluminum and Plastic PETG are 3D printed: their properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is DMLS AlSi10Mg Aluminum stronger than Plastic PETG?
DMLS AlSi10Mg Aluminum is stronger: its yield strength is 270 MPa against 46.2 MPa for Plastic PETG (5.84x).
Which is lighter, DMLS AlSi10Mg Aluminum or Plastic PETG?
Plastic PETG is lighter: 1,270 kg/m³ against 2,670 kg/m³ for DMLS AlSi10Mg Aluminum.
Which is stiffer, DMLS AlSi10Mg Aluminum or Plastic PETG?
DMLS AlSi10Mg Aluminum is stiffer: Young's modulus 72 GPa against 1.94 GPa for Plastic PETG, so the same part in DMLS AlSi10Mg Aluminum deflects less under the same load.
Which is lighter for the same job, DMLS AlSi10Mg Aluminum or Plastic PETG?
For the same stiffness or strength: DMLS AlSi10Mg Aluminum is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
| Part that must be | DMLS AlSi10Mg Aluminum | Plastic PETG |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 17.7x heavier |
| Stiff beam (bending) | lighter | 2.9x heavier |
| Stiff panel or plate | lighter | 1.59x heavier |
| Strong rod or tie | lighter | 2.78x heavier |
| Strong beam | lighter | 1.54x heavier |
| Strong panel or plate | lighter | 15% heavier |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, DMLS AlSi10Mg Aluminum or Plastic PETG?
DMLS AlSi10Mg Aluminum stretches further before it breaks: 10.2% elongation at break against 7.6% for Plastic PETG.
Thermal
Which conducts heat better, DMLS AlSi10Mg Aluminum or Plastic PETG?
DMLS AlSi10Mg Aluminum conducts heat better: 110 W/m·K against 0.21 W/m·K for Plastic PETG.
Which expands less with temperature?
DMLS AlSi10Mg Aluminum expands less: 20 µm/m·K against 51 µm/m·K for Plastic PETG.
Related comparisons
- DMLS AlSi10Mg Aluminum vs. Aluminum
- DMLS AlSi10Mg Aluminum vs. Aluminum 6061-T6
- DMLS AlSi10Mg Aluminum vs. Aluminum 2024-T351
- DMLS AlSi10Mg Aluminum vs. Aluminum 6063-T6
- Plastic PETG vs. SLA Resin Tough 2000
- Plastic PETG vs. Plastic ABS
- Plastic PETG vs. FDM Polycarbonate
- Plastic PETG vs. Plastic ABS (bulk/injection)