Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
Sources3 documents: Special Metals, BASF Forward AM, INEOS Styrolution
FDM HIPS
BASF Forward AM (BASF 3D Printing Solutions) Ultrafuse HiPS, TDS v2.2 (13.11.2019), printed specimens, XY 'Flat'. Specimen print settings are not stated; recommended processing on the sheet: nozzle 240-260 °C, bed 100-120 °C, 40-80 mm/s. Product is discontinued (Forward AM product page) but the TDS is still served by Forward AM.
Nickel Inconel 718
INCONEL alloy 718, standard grade, 1750 °F/1 hr anneal + 1325 °F/8 hr F.C. to 1150 °F aged; Special Metals bulletin SMC-045 typical values
1
INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
FDM HIPS is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is FDM HIPS stronger than Nickel Inconel 718?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against tensile strength 18.4 MPa for FDM HIPS (65.6x).
Which is lighter, FDM HIPS or Nickel Inconel 718?
FDM HIPS is lighter: 1,023 kg/m³ against 8,221 kg/m³ for Nickel Inconel 718.
Which is stiffer, FDM HIPS or Nickel Inconel 718?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 1.59 GPa for FDM HIPS, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, FDM HIPS or Nickel Inconel 718?
For the same stiffness or strength: FDM HIPS is lighter for a stiff panel or plate; Nickel Inconel 718 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam.
Part that must be
FDM HIPS
Nickel Inconel 718
Stiff rod or tie (tension)
15.7x heavier
lighter
Stiff beam (bending)
40% heavier
lighter
Stiff panel or plate
lighter
1.6x heavier
Strong rod or tie
8.16x heavier
lighter
Strong beam
2.02x heavier
lighter
Strong panel or plate
about equal
about equal
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, FDM HIPS or Nickel Inconel 718?
Nickel Inconel 718 stretches further before it breaks: 20% elongation at break against 1.4% for FDM HIPS.
Thermal
Which conducts heat better, FDM HIPS or Nickel Inconel 718?
Nickel Inconel 718 conducts heat better: 11.4 W/m·K against 0.17 W/m·K for FDM HIPS.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 80 µm/m·K for FDM HIPS.