Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
INCONEL alloy 718, standard grade, 1750 °F/1 hr anneal + 1325 °F/8 hr F.C. to 1150 °F aged; Special Metals bulletin SMC-045 typical values
Plastic UHMWPE
Celanese GUR 4120 (avg. molecular weight 4.7x10^6 g/mol), typical values on compression-molded specimens; CTE and thermal conductivity from Celanese's generic UHMWPE guide (grade not named)
1
INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
2
GUR UHMW-PE Overview (GUR-015)CelanesePlastic UHMWPE · Yield strength: typical, tensile stress at yield ISO 527, 50 mm/minPlastic UHMWPE · Ultimate tensile strength: typical, tensile stress at break ISO 527, 50 mm/minPlastic UHMWPE · Elongation at break: typical, nominal elongation at break ISO 527Plastic UHMWPE · Young's modulus (stiffness): typical, tensile modulus ISO 527, 1 mm/minPlastic UHMWPE · Density: typicalPlastic UHMWPE · Melting point: DSC 10 K/minPlastic UHMWPE · Max service temperature: recommended max constant operating temperature
3
GUR UHMW-PE Polymer Guide (GUR-003)Celanesearchived copyPlastic UHMWPE · Thermal conductivity: typical, unfilled (narrative value, generic Celanese UHMWPE)Plastic UHMWPE · Thermal expansion: typical, 20 to 100 °C (generic Celanese UHMWPE)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Nickel Inconel 718 stronger than Plastic UHMWPE?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 20 MPa for Plastic UHMWPE (60.4x).
Which is lighter, Nickel Inconel 718 or Plastic UHMWPE?
Plastic UHMWPE is lighter: 930 kg/m³ against 8,221 kg/m³ for Nickel Inconel 718.
Which is stiffer, Nickel Inconel 718 or Plastic UHMWPE?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 0.66 GPa for Plastic UHMWPE, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Nickel Inconel 718 or Plastic UHMWPE?
For the same stiffness or strength: Nickel Inconel 718 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie, strong beam; Plastic UHMWPE is lighter for a stiff panel or plate, strong panel or plate.
Part that must be
Nickel Inconel 718
Plastic UHMWPE
Stiff rod or tie (tension)
lighter
34.3x heavier
Stiff beam (bending)
lighter
1.97x heavier
Stiff panel or plate
32% heavier
lighter
Strong rod or tie
lighter
6.83x heavier
Strong beam
lighter
1.74x heavier
Strong panel or plate
14% heavier
lighter
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Nickel Inconel 718 or Plastic UHMWPE?
Plastic UHMWPE stretches further before it breaks: 465% elongation at break against 20% for Nickel Inconel 718.
Thermal
Which handles higher temperatures, Nickel Inconel 718 or Plastic UHMWPE?
Nickel Inconel 718 does: 704 °C against 80 °C for Plastic UHMWPE.
Which conducts heat better, Nickel Inconel 718 or Plastic UHMWPE?
Nickel Inconel 718 conducts heat better: 11.4 W/m·K against 0.4 W/m·K for Plastic UHMWPE.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 200 µm/m·K for Plastic UHMWPE.