Materials / Compare
Nickel Inconel 718 vs. Plastic Nylon
Compare Nickel Inconel 718 vs. Plastic Nylon strength, stiffness, weight and thermal properties.
| Mechanical | Nickel Inconel 718 | Plastic Nylon |
|---|---|---|
| Yield strength | 1,207MPa119.1x stronger | 63.1MPa2 |
| Ultimate tensile strength | 1,389MPa122x stronger | 63.1MPa2 |
| Flexural strength | not sourced | 82.9MPa2 |
| Elongation at break | 20%1 | not sourced |
| Young's modulus (stiffness) | 200GPa185.8x stiffer | 2.33GPa2 |
| Density | 8,221kg/m³1 | 1,140kg/m³27.21x lighter |
| Strength to weight | 147kN·m/kg2.65x higher | 55.4kN·m/kg |
| Stiffness to weight | 24.3MN·m/kg11.9x higher | 2.04MN·m/kg |
| Poisson's ratio | 0.2941 | base material0.43 |
| Shear modulus | 77.3GPa92.8x stiffer in shear | 0.833GPa |
| Bulk modulus | 162GPa41.7x higher | 3.89GPa |
| Speed of sound | 4,932m/s3.45x faster | 1,430m/s |
| Thermal | Nickel Inconel 718 | Plastic Nylon |
|---|---|---|
| Thermal conductivity | 11.4W/m·K134.5x more heat through a fin | base material0.33W/m·K4 |
| Thermal expansion | 13.2µm/m·K1 | base material98–102µm/m·K4 |
| 100 mm part over a 50 °C swing | 66µm growth7.58x less | 500µm growth |
| Specific heat | 435J/kg·K1 | base material1,700J/kg·K43.91x higher |
| Heats up and cools (diffusivity) | 3.19mm²/s18.7x faster | 0.17mm²/s |
| Thermal shock resistance | 3,680W/m68.7x more resistant | 53.6W/m |
| Melting point | melting range1,260–1,336°C1 | 188°C2 |
| Glass transition | not sourced | 55.1°C2 |
| Max service temperature | 704°C1 | HDT 0.455 MPa89.2°C2 |
| Try it on a partA bracket to run stress or thermal on, free in your browser | Open in LessCAD | Open in LessCAD |
|---|
Sources4 documents: Special Metals, UltiMaker, Covestro, BASF
- Nickel Inconel 718
- INCONEL alloy 718, standard grade, 1750 °F/1 hr anneal + 1325 °F/8 hr F.C. to 1150 °F aged; Special Metals bulletin SMC-045 typical values
- Plastic Nylon
- Ultimaker Nylon, 3D-printed specimens, XY (flat), conditioned >=24 h at room temperature; Ultimaker S5 Pro, engineering intent profile, 0.15 mm layer height, AA 0.4 print core, 100% infill, Cura 4.9, printed one-at-a-time, conditioned >=24 h at room temperature. TDS v2.00, April 20, 2022.
- 1INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
- 2Ultimaker Nylon Technical Data Sheet, v5.00UltiMakerarchived copyPlastic Nylon · Yield strength: typicalPlastic Nylon · Ultimate tensile strength: typical, peak stress (= stress at yield)Plastic Nylon · Flexural strength: typicalPlastic Nylon · Young's modulus (stiffness): typicalPlastic Nylon · Density: typicalPlastic Nylon · Melting point: typicalPlastic Nylon · Glass transition: typicalPlastic Nylon · Max service temperature: HDT 0.455 MPa (printed specimens)
- 3Engineering Polymers Part and Mold Design: Thermoplastics, A Design GuideCovestroPlastic Nylon · Poisson's ratio: base material: unfilled polyamide (PA), conditioned, maker design-guide family value (Covestro Table 3-1)
- 4Ultramid (PA) Product RangeBASFPlastic Nylon · Thermal conductivity: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)Plastic Nylon · Thermal expansion: base material: unreinforced BASF Ultramid PA66 (A3K, 98) and PA6 (B3S, 102), 23-55 CPlastic Nylon · Specific heat: base material: unreinforced BASF Ultramid PA66 (A3K) and PA6 (B3S), 23 C (same value for both)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Plastic Nylon is 3D printed: its properties depend on build direction and print settings; these are typical values.
Questions
Mechanical
Is Nickel Inconel 718 stronger than Plastic Nylon?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 63.1 MPa for Plastic Nylon (19.1x).
Which is lighter, Nickel Inconel 718 or Plastic Nylon?
Plastic Nylon is lighter: 1,140 kg/m³ against 8,221 kg/m³ for Nickel Inconel 718.
Which is stiffer, Nickel Inconel 718 or Plastic Nylon?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 2.33 GPa for Plastic Nylon, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Nickel Inconel 718 or Plastic Nylon?
For the same stiffness or strength: Nickel Inconel 718 is lighter for a stiff rod or tie (tension), stiff beam (bending), strong rod or tie; Plastic Nylon is lighter for a stiff panel or plate, strong panel or plate.
| Part that must be | Nickel Inconel 718 | Plastic Nylon |
|---|---|---|
| Stiff rod or tie (tension) | lighter | 11.9x heavier |
| Stiff beam (bending) | lighter | 28% heavier |
| Stiff panel or plate | 1.64x heavier | lighter |
| Strong rod or tie | lighter | 2.65x heavier |
| Strong beam | about equal | about equal |
| Strong panel or plate | 1.65x heavier | lighter |
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Thermal
Which conducts heat better, Nickel Inconel 718 or Plastic Nylon?
Nickel Inconel 718 conducts heat better: 11.4 W/m·K against 0.33 W/m·K for Plastic Nylon.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 100 µm/m·K for Plastic Nylon.
Related comparisons
- Nickel Inconel 718 vs. Stainless Steel 17-4PH
- Nickel Inconel 718 vs. Steel AISI 4340
- Nickel Inconel 718 vs. DMLS 17-4PH Stainless Steel
- Nickel Inconel 718 vs. Steel AISI 1045
- Plastic Nylon vs. Plastic Polycarbonate
- Plastic Nylon vs. FDM Polycarbonate
- Plastic Nylon vs. SLA Resin Standard
- Plastic Nylon vs. Plastic POM/Acetal