Thermal conductivity against densityHigher and further left: spreads more heat for its weightThermal expansion against thermal conductivityLower and further right: warps less when heated
Try it on a partA bracket to run stress or thermal on, free in your browser
INCONEL alloy 718 (SMC-045)Special Metalsarchived copyNickel Inconel 718 · Yield strength: typical, 1.0 in. hot-rolled bar, 0.2% offsetNickel Inconel 718 · Ultimate tensile strength: typical, 1.0 in. barNickel Inconel 718 · Elongation at break: typical, 1.0 in. barNickel Inconel 718 · Young's modulus (stiffness): typical, 21 °C, annealed + agedNickel Inconel 718 · Density: nominal, annealed and agedNickel Inconel 718 · Poisson's ratio: typical, 21 °C, annealed + agedNickel Inconel 718 · Thermal conductivity: typical, 21 °C, annealed + aged (calculated from resistivity per footnote a)Nickel Inconel 718 · Thermal expansion: typical, mean 21-93 °C, annealed + agedNickel Inconel 718 · Specific heat: typical, 21 °CNickel Inconel 718 · Melting point: melting rangeNickel Inconel 718 · Max service temperature: upper use temperature stated by producer
3
MIL-HDBK-5J, Metallic Materials and Elements for Aerospace Vehicle Structures (2003)U.S. Department of DefenseAluminum 7050-T7451 · Poisson's ratio: typical (handbook physical constant)
Each number points to the document that states it, with the exact basis. Values without a number are computed from the sourced ones. "Not sourced" means no citable source states it (or only a specification minimum); figures computed from it are left out too.
Questions
Mechanical
Is Aluminum 7050-T7451 stronger than Nickel Inconel 718?
Nickel Inconel 718 is stronger: its yield strength is 1,207 MPa against 469 MPa for Aluminum 7050-T7451 (2.57x).
Which is lighter, Aluminum 7050-T7451 or Nickel Inconel 718?
Aluminum 7050-T7451 is lighter: 2,830 kg/m³ against 8,221 kg/m³ for Nickel Inconel 718.
Which is stiffer, Aluminum 7050-T7451 or Nickel Inconel 718?
Nickel Inconel 718 is stiffer: Young's modulus 200 GPa against 70.3 GPa for Aluminum 7050-T7451, so the same part in Nickel Inconel 718 deflects less under the same load.
Which is lighter for the same job, Aluminum 7050-T7451 or Nickel Inconel 718?
For the same stiffness or strength: Aluminum 7050-T7451 is lighter for a stiff rod or tie (tension), stiff beam (bending), stiff panel or plate, strong rod or tie, strong beam, strong panel or plate.
Part that must be
Aluminum 7050-T7451
Nickel Inconel 718
Stiff rod or tie (tension)
lighter
2% heavier
Stiff beam (bending)
lighter
1.72x heavier
Stiff panel or plate
lighter
2.05x heavier
Strong rod or tie
lighter
13% heavier
Strong beam
lighter
1.55x heavier
Strong panel or plate
lighter
1.81x heavier
For the same stiffness or strength, mass scales with density over stiffness (or strength) raised to a power set by how the part is loaded: 1 for a rod in tension, 1/2 for a beam in bending, 1/3 for a panel (the standard material-selection indices).
Which is more ductile, Aluminum 7050-T7451 or Nickel Inconel 718?
Nickel Inconel 718 stretches further before it breaks: 20% elongation at break against 11% for Aluminum 7050-T7451.
Thermal
Which conducts heat better, Aluminum 7050-T7451 or Nickel Inconel 718?
Aluminum 7050-T7451 conducts heat better: 157 W/m·K against 11.4 W/m·K for Nickel Inconel 718.
Which expands less with temperature?
Nickel Inconel 718 expands less: 13.2 µm/m·K against 23.5 µm/m·K for Aluminum 7050-T7451.